南昌啤酒厂二氧化碳储罐

维护与检修 Maintenance and repair
【产品详情图片】
1.储罐的使用与维护，应按“压力容器安全技术监察规程”要求和本说明进行。
The use and maintenance of the storage tank shall be carried out according to the requirements of the Pressure Vessel Safety Technical Supervision Regulations and these instructions
2.日常检查与维护 Daily inspection and maintenance
储罐在运行过程中，要经常检查安全阀、压力表、液位计工作是否正常，阀门管路是否有泄漏，外部有无异常现象，发现问题及时处理。
During operation of the tank, check the safety valve, pressure gauge and liquid level meter regularly, whether the valve line is leaking, whether there is any abnormal phenomenon outside, and find the problem to be handled in time.
3.定期校验 Regular verification
3.1安全阀整定压力不大于2.27Mpa，每年至少校验一次，并加铅封，作好记录。
Safety valve setting pressure is not more than 2.27Mpa, at least once a year, and add seals, make a record.
3.2定期检查夹层真空度，未装低温介质的情况下真空度应低于65Pa，装有低温介质的情况下，真空度应低于10Pa为合格。
Regularly check the sandwich vacuum, the vacuum should be less then 65Pa without vacuum medium; with a low temperature medium, the vacuum should be less than 10Pa for the pass.
【产品详情图片】
【标题】

储罐的增压 Tank pressurization
【产品详情图片】
当储罐向外供液又需要稳定排液压力时，可利用汽化器（另外配备）进行增压。其操作过程如下：
The carburetor (available separately) can be used for boosting when the reservoir is supplied externally and requires stable discharge pressure. The operation is as follows:
2.3.1开启V2排液阀，使液体二氧化碳汽化器汽化，开启V3回气阀（根据用户回气管路的设置，V3回气阀可置于常开状态）从汽化器分流出来的气体返回储罐上部，使储罐内增压。
Open the V2 drain valve to vaporize the liquid carbon dioxide vaporizer and open the V3 return valve (the V3 return valve can be normally open depending on the return air line of the user). The gas diverted from the vaporizer returns to the upper part of the tank , So that the pressure tank.
2.3.2当储罐内压力达到2.1Mpa时，可暂时关闭V3回气阀。
When the tank pressure reaches 2.1Mpa, the valve can be temporarily closed V3 return gas valve.
2.3.3排液过程中，可通过控制V3回气阀的开度，使增压能力维持在压力稳定的水平。
During drainage, the degree of pressurization can be maintained at a pressure-stable level by controlling the opening of the V3 return valve.
【产品详情图片】

2 储罐的操作Tank operation
【产品详情图片】
储罐的操作分为充液、贮存、增压、排液等过程，每个过程必须做到：V6三通截止阀（连接安全阀）和V8液位计组合阀始终处于全开状态。罐内压力不应高于2.16Mpa，压力不应低于0.8Mpa .
The operation of the tank is divided into filling, storage, pressurization, drainage and other processes, each process must be: V6 three-way valve (connecting safety valve) and V8 level gauge combination valve is always in the fully open state. Tank maximum pressure should not exceed 2.16Mpa, the minimum pressure should not be less than 0.8Mpa.
【产品详情图片】
【主变量】【变量3】【变量2】【变量1】

结构说明 Structure Description
1. 泄放装置 Discharge device
2. 内胆 Liner
3.保温层(珠光砂) Insulation (pear sand)
4.外壳 Shell
5.仪表(差压计、氧压表、组合阀) Meter (differential pressure gauge, oxygen pressure gauge, combination valve)
6.抽空口及真空阀门Evacuation port and vacuum valve
7.管路阀门 Pipeline Valve
说 明Description:
⑴本储罐的操作系统多集中于储罐底部，仪表系统及组合阀设置在筒壁，便于观察操作.
The operating system of the tank and more concentrated in the bottom of the tank, instrument system and valve combination set in the cylinder wall, easy to observe the operation.
(2) 内胆设置有两个安全阀S1、S2，夹层泄压装置B。
There are two safety valves S1, S2 inside the liner, sandwich pressure relief device B.
(3) 连接形式：进液口→2＂螺纹连接，排液阀→2＂螺纹连接，抽空口→法兰.
Connection: inlet → 2 "thread connection, drain valve → 2" thread connection, exhaust port → flange.
【产品详情图片】
【变量3】【变量2】【变量1】

http://zhongjiezhuangbei.com