崇左二氧化碳储罐

液体的储存 liquid storage
液体二氧化碳的储存属于带压（压力不低于0.8Mpa）储存。储存期间除压力表、液位计、安全阀应投入使用外，其他阀门应处于关闭状态。当储罐压力超过2.1Mpa时，开启V7排气阀降压。但应注意：内罐的压力不得降至低于0.8Mpa，否则将引起液体二氧化碳转变为干冰。
Liquid carbon dioxide storage with pressure (pressure not less than 0.8Mpa) storage. During the storage, the pressure gauge,level gauge, safety valve should be put into use, the other valves should be closed. When the tank pressure exceeds 2.1Mpa, open the V7 exhaust valve buck. However, it should be noted that the pressure inside the tank must not drop below 0.8Mpa, otherwise liquid carbon dioxide will be converted to dry ice.
【产品详情图片】
【标题】

二氧化碳储罐的结构和安全特性
夹层封结后真空度规范为有效容积：小于等于10m3真空度≤ 2Pa大于10m3小于等于50m3真空度≤3Pa大于50m3小于等于100m3真空度≤
5Pa以精深的技能它作用主要是用来储存：油田清洗机，液态二氧化碳(LCO2功能方面：绝热资料选用热态下的珠光砂充填夹层并抽真空。共同的填充技术，质量保证许诺，以达到的绝热作用。
为真空粉末绝热型式低温液态二氧化碳储罐构造为表里容器构成的双层容器。可分卧式和立式两类，内容器资料选 16MnDR外容器资料可根据用户区域不一样选 Q235-B或 16MnR内、外容器夹层充填绝热资料珠光砂并抽真空。
安全阀定时校验时可封闭一侧，低温液体二氧化碳储罐选用 组合、安全体系阀”运用两组安全阀一起作业。另一侧持续作业，保证储罐的安全运转。

充液的操作 filling operation
【标题】
充液分为充液和补充充液。
充液的操作如下：
Filling fluid is divided into the first filling and filling fluid.
The first filling operation is as follows:
2.1.1 储罐吹除置换干净达到要求后，将充液管线与储罐的充液接头连接，液位计组合阀处于平衡状态准备充液。
After the tank blows off to replace the cleanliness meets the requirements, the filling liquid line is connected with the liquid filling joint of the tank, and the liquid level gauge combination valve is in an equilibrium state to be filled.
2.1.2充入与液体二氧化碳纯度相同的气体，使罐内压力达到0.8 Mpa以上，方可进行充液。 filled with the same purity of liquid carbon dioxide gas, the tank pressure reached 0.8 Mpa above, before filling.
2.1.3 将充液管线接通槽车，先开启V5残液阀，排出管线内的杂质气体后，再开启V1进液阀和V7排气阀，V8液位计组合阀处于全开状态，显示液位计读数进行充液。
The filling liquid line connected tanker, first open the V5 raffinate valve, exhaust gas impurities within the pipeline, and then open the V1 inlet valve and V7 exhaust valve, V8 level gauge combination valve is fully open state, Display level meter readings are filled.
2.1.4 在充液过程中，当液位计指示液位接近标定值时，可间断开启V4充满指示阀，如有液体喷出，应立即停止充液，关闭V4充满指示阀。
During the filling process, when the liquid level gauge indicates the liquid level approaches the calibration value, the V4 may be intermittently opened to indicate the valve. If any liquid is ejected, liquid filling should be stopped immediately and the V4 valve should be closed.
2.1.5关闭V1进液阀和V7排气阀，打开V5残液阀，拆下充液管线，充液结束。
补充充液的操作与充液的操作方法相似，不同点是补充充液时一开始就可以大量充液。
Close the V1 inlet valve and the V7 exhaust valve, open the V5 residual valve, remove the filling line, and fill with liquid.
The procedure for replenishing the priming solution is the same as for the first priming procedure, except that the priming solution can be replenished extensively from the beginning.
【产品详情图片】
【标题】

储罐的增压 Tank pressurization
【产品详情图片】
当储罐向外供液又需要稳定排液压力时，可利用汽化器（另外配备）进行增压。其操作过程如下：
The carburetor (available separately) can be used for boosting when the reservoir is supplied externally and requires stable discharge pressure. The operation is as follows:
2.3.1开启V2排液阀，使液体二氧化碳汽化器汽化，开启V3回气阀（根据用户回气管路的设置，V3回气阀可置于常开状态）从汽化器分流出来的气体返回储罐上部，使储罐内增压。
Open the V2 drain valve to vaporize the liquid carbon dioxide vaporizer and open the V3 return valve (the V3 return valve can be normally open depending on the return air line of the user). The gas diverted from the vaporizer returns to the upper part of the tank , So that the pressure tank.
2.3.2当储罐内压力达到2.1Mpa时，可暂时关闭V3回气阀。
When the tank pressure reaches 2.1Mpa, the valve can be temporarily closed V3 return gas valve.
2.3.3排液过程中，可通过控制V3回气阀的开度，使增压能力维持在压力稳定的水平。
During drainage, the degree of pressurization can be maintained at a pressure-stable level by controlling the opening of the V3 return valve.
【产品详情图片】

http://zhongjiezhuangbei.com