钦州钢构用二氧化碳储罐

1、高纯二氧化碳主要用于电子工业，用于配制其它特种混台气，在聚乙烯聚合反应中则用作调节剂。
2、固态二氧化碳广泛用于冷藏百奶制品、肉类、冷冻食品和其它转运中易的食品，在许多工业加工中作为冷冻剂。
3、气态二氧化碳用于碳化软度饮料、食品保存、化学和食品加工过程的惰性保护、焊接气体、植物生长剂。
4、液体二氧化碳用作致冷剂，飞机、和电子部件的低温试验，提高油井采收率，问橡胶磨光以及控制化学反应，也可用作灭火剂。

常见故障的处理 Common fault handling
【产品详情图片】
1.内罐压力异常长高 Inner tank pressure abnormally high
1.1可能是V3回气阀开度过大或阀门失灵，应减小阀门开度或检修阀门。
May be V3 return valve opening is too large or valve failure, should reduce the valve opening or valve repair.
1.2可能是S1、S2安全阀失灵，到启动压力不启动，应检查安全阀。
may be S1, S2 safety valve failure, to start the pressure does not start, check the safety valve.
1.3可能是压力表指示不准确，应校验压力表。
may be pressure gauge indicates inaccurate, should verify the pressure gauge.
2.液位计指示不真实 Level gauge instructions are not true
2.1可能是液位计失灵，应检修液位计。
may be the level gauge failure, should be maintenance level gauge
2.2可能是液位计接头处泄漏，应检修接头连接处，排除泄漏。
It may be a leak at the head of the liquid level gauge. It should repair the connection of the joint and eliminate the leakage
3.蒸发率高，外壳体凝水结霜 High evaporation rate, the outer shell condensate frost
3.1可能是珠光砂未填实或下沉，应补充珠光砂，重新抽真空。
may be unfilled or sinking of pearl sand, pearl sand should be added and re-evacuated.
3.2可能是真空度恶化，应进行真空检漏，重新抽真空。
may be a deterioration of the vacuum, vacuum leak detection should be carried out, re-vacuum.
4.管道阀门液体流动不畅或堵塞 pipeline valve fluid flow or blocked
可能是液体二氧化碳形成干冰的原因造成，应停止使用，用热空气加温管阀至畅通为止。May be caused by the formation of dry ice, should stop using, with hot air heating pipe valve until smooth.
【产品详情图片】
【标题】

维护与检修 Maintenance and repair
【产品详情图片】
1.储罐的使用与维护，应按“压力容器安全技术监察规程”要求和本说明进行。
The use and maintenance of the storage tank shall be carried out according to the requirements of the Pressure Vessel Safety Technical Supervision Regulations and these instructions
2.日常检查与维护 Daily inspection and maintenance
储罐在运行过程中，要经常检查安全阀、压力表、液位计工作是否正常，阀门管路是否有泄漏，外部有无异常现象，发现问题及时处理。
During operation of the tank, check the safety valve, pressure gauge and liquid level meter regularly, whether the valve line is leaking, whether there is any abnormal phenomenon outside, and find the problem to be handled in time.
3.定期校验 Regular verification
3.1安全阀整定压力不大于2.27Mpa，每年至少校验一次，并加铅封，作好记录。
Safety valve setting pressure is not more than 2.27Mpa, at least once a year, and add seals, make a record.
3.2定期检查夹层真空度，未装低温介质的情况下真空度应低于65Pa，装有低温介质的情况下，真空度应低于10Pa为合格。
Regularly check the sandwich vacuum, the vacuum should be less then 65Pa without vacuum medium; with a low temperature medium, the vacuum should be less than 10Pa for the pass.
【产品详情图片】
【标题】

储罐的增压 Tank pressurization
【产品详情图片】
当储罐向外供液又需要稳定排液压力时，可利用汽化器（另外配备）进行增压。其操作过程如下：
The carburetor (available separately) can be used for boosting when the reservoir is supplied externally and requires stable discharge pressure. The operation is as follows:
2.3.1开启V2排液阀，使液体二氧化碳汽化器汽化，开启V3回气阀（根据用户回气管路的设置，V3回气阀可置于常开状态）从汽化器分流出来的气体返回储罐上部，使储罐内增压。
Open the V2 drain valve to vaporize the liquid carbon dioxide vaporizer and open the V3 return valve (the V3 return valve can be normally open depending on the return air line of the user). The gas diverted from the vaporizer returns to the upper part of the tank , So that the pressure tank.
2.3.2当储罐内压力达到2.1Mpa时，可暂时关闭V3回气阀。
When the tank pressure reaches 2.1Mpa, the valve can be temporarily closed V3 return gas valve.
2.3.3排液过程中，可通过控制V3回气阀的开度，使增压能力维持在压力稳定的水平。
During drainage, the degree of pressurization can be maintained at a pressure-stable level by controlling the opening of the V3 return valve.
【产品详情图片】

http://zhongjiezhuangbei.com